User:Jgt/sandbox matlab: Difference between revisions
From HPC Wiki
< User:Jgt
No edit summary |
|||
| (4 intermediate revisions by the same user not shown) | |||
| Line 2: | Line 2: | ||
=Preliminaries= | =Preliminaries= | ||
{{Cmd|module keyword matlab|output=<pre> | {{Cmd | ||
|module keyword matlab | |||
|output= | |||
<pre> | |||
matlab/r2018a : plot math graphics matlab | matlab/r2018a : plot math graphics matlab | ||
octave/4.2.1 : plot matlab octave | octave/4.2.1 : plot matlab octave | ||
</pre>}} | </pre> | ||
}} | |||
{{Cmd|module load matlab}} | {{Cmd|module load matlab}} | ||
{{Cmd|module load matlab/r2018a}} | {{Cmd|module load matlab/r2018a}} | ||
{{Cmd|module list|output=<pre> | {{Cmd | ||
|module list | |||
|output= | |||
<pre> | |||
Currently Loaded Modulefiles: | Currently Loaded Modulefiles: | ||
1) matlab/r2018a | 1) matlab/r2018a | ||
</pre>}} | </pre> | ||
}} | |||
=Interactive Session - No GUI= | =Interactive Session - No GUI= | ||
{{Cmd|module load matlab|matlab -nodesktop -nodisplay -nosplash|output=<pre> | |||
{{Cmd | |||
|srun -p float -n 2 --pty -t 03:00:00 bash | |||
|module load matlab | |||
|matlab -nodesktop -nodisplay -nosplash | |||
|output= | |||
<pre> | |||
< M A T L A B (R) > | < M A T L A B (R) > | ||
| Line 31: | Line 45: | ||
>> helloWorld | >> helloWorld | ||
Hello, World! | Hello, World! | ||
</pre>}} | </pre> | ||
}} | |||
=Interactive Session - GUI= | =Interactive Session - GUI= | ||
To use the MATLAB graphical user interface (GUI) remotely, you will need to enable X11 forwarding over SSH by adding -X (Note: X is capitalized) to the ssh command when logging into Magnolia. | |||
{{Cmd|ssh user@magnolia.usm.edu -X}} | |||
Once on Magnolia, start an interactive bash session by running the srun command below. This will create an interactive session on the float partition that uses two processors with a time limit of three hours. The --x11 flag has been added to enable X11 forwarding. | |||
{{Cmd|srun -p float -n 2 --pty --x11 -t 03:00:00 bash}} | |||
Then make sure that you are not on one of the head nodes (magnolia01/magnolia02) and load the matlab module into the environment. Once this is complete, simply type matlab into the prompt and the GUI should appear on your desktop. | |||
{{Cmd | |||
|module load matlab | |||
|matlab | |||
|output= | |||
<pre> | |||
MATLAB is selecting SOFTWARE OPENGL rendering. | |||
</pre> | |||
}} | |||
=Non-Interactive Batch Job= | =Non-Interactive Batch Job= | ||
Latest revision as of 09:44, 19 September 2018
Preliminaries
user $module keyword matlab
matlab/r2018a : plot math graphics matlab octave/4.2.1 : plot matlab octave
user $module load matlabuser $module load matlab/r2018auser $module list
Currently Loaded Modulefiles: 1) matlab/r2018a
Interactive Session - No GUI
user $srun -p float -n 2 --pty -t 03:00:00 bash
user $module load matlab
user $matlab -nodesktop -nodisplay -nosplash
< M A T L A B (R) >
Copyright 1984-2018 The MathWorks, Inc.
R2018a (9.4.0.813654) 64-bit (glnxa64)
February 23, 2018
To get started, type one of these: helpwin, helpdesk, or demo.
For product information, visit www.mathworks.com.
>> disp('Hello, World!')
Hello, World!
>> helloWorld
Hello, World!
Interactive Session - GUI
To use the MATLAB graphical user interface (GUI) remotely, you will need to enable X11 forwarding over SSH by adding -X (Note: X is capitalized) to the ssh command when logging into Magnolia.
user $ssh user@magnolia.usm.edu -XOnce on Magnolia, start an interactive bash session by running the srun command below. This will create an interactive session on the float partition that uses two processors with a time limit of three hours. The --x11 flag has been added to enable X11 forwarding.
user $srun -p float -n 2 --pty --x11 -t 03:00:00 bashThen make sure that you are not on one of the head nodes (magnolia01/magnolia02) and load the matlab module into the environment. Once this is complete, simply type matlab into the prompt and the GUI should appear on your desktop.
user $module load matlab
user $matlab
MATLAB is selecting SOFTWARE OPENGL rendering.